2022 John Deere Sugar Cane CH960
- Year 2022
- Make John Deere
- Model Sugar Cane
- Engine Model: 6136NW301
2022 John Deere Sugar Cane CH960
Sugar Cane Harvester- For row spacing from 5 ft. 7 in. to 6 ft. 3 in. (1.7 to 1.9 m)
- Redesigned cleaning system reduces cane loss
- Increased pour rate reduces harvesting cost per ton1
- Controlled Traffic feature matches tread to row spacing
- 13.6 L PowerTech™ Engine
Features may include:
Double productivity without increasing speed- The John Deere CH9 Series Two-Row Harvester provides double the productivity of a single row-unit in most conditions by harvesting two rows of cane simultaneously at the same speed.
- Loads wagon in half the time
- Reduces infield transport requirement by 28 percent
- Reduces fuel consumption by 30 percent
- 36 percent fewer operators are needed
- Functionality:
- Since the CH9 Series models harvest at the same speed as the single-row units in most conditions, the wagons are loaded in half the time, reducing total infield transport equipment cycle time considerably. In a typical operation, this translates into 50 percent fewer harvesters, 28 percent fewer tractors and wagons, and 36 percent fewer operators required per front while saving 30 percent in fuel. In multi-front operations, this additional harvesting capacity can also be used to decrease the number of fronts by increasing their quotas. Regardless of the solution adopted, the total number of operators, tractors, wagons, and harvesters is reduced significantly.
- The CH9 Series tread matches the row spacing so the tracks travel centered on the interrow away from the stubble. By straddling two rows, the center interrow remains untouched, leaving 50 percent of the rows are undisturbed. In addition, the compacted area is reduced by 60 percent, fostering better growing conditions for improved yield and ratoon life.
- Matching tread to row spacing
- 60 percent less compacted area
- Untouched center interrow for 50 percent of rows undisturbed
- Improves yield and ratoon life
- 30 to 50 percent cane loss reduction
- Functionality:
- By straddling two rows, the center interrow remains untouched so 50 percent of the rows are undisturbed. In addition, the compacted area is reduced by 60 percent. Thanks to better cane growing conditions fostered by the John Deere two-row harvester system, improved yield and ratoon life are expected.
- Wider entry to the primary extractor, less billet contact with the fan, and a 78 percent larger secondary extractor reduce cane loss while maintaining low extraneous matter levels. In addition, only 50 percent of the uncut rows are exposed to contact with the harvester for further loss reduction.
- Low extraneous matter levels
- 30 to 50 percent cane loss reduction
- Operate at low fan rpm to save fuel
- Functionality:
- Twice the pour rate of a single-row unit required reengineering of the cleaning system to deliver high-quality cane. The CH9 Series Sugar Cane Harvester optimizes the use of the primary extractor cleaning area with wider entry offered by the longer chopper drums. It is in this first section where most of the trash removal takes place. Relocating the fan further back and tapering the cane inlet greatly contributes to cleaning efficiency and reduced loss.
Engine
							Engine Manufacturer
							John Deere
						
						
							Engine Power
							Standard power @ 2100 rpm: 485 hp / 360 kW / 490 CV | Standard power @ 1900 rpm: 485 hp / 360 kW / 490 CV | Standard power @ 1700 rpm: 540 hp / 400 kW / 544 CV
						
						
							Engine
							Model: 6136NW301
						
						
							Displacement
							830 cu in. (13.6 L)
						
						
							Cooling System
							Automatically controlled, hydraulically driven reversing cooling fan
						
						
							Emissions
							Tier 3/Stage III A
						
						
							Cylinder Liners
							Inline six, wet sleeves
						
						
							Aspiration
							Turbocharger with air-to-air aftercooling
						
						
							Injection Pump Type
							Electronically controlled
						
						
							Rated Engine Speed
							Low idle: 800 rpm / Full throttle: 1900 rpm
						
						Drivetrain
							Transmission
							Two hydrostatic pumps providing variable speed
						
						
							Drive System
							Topper: Hydraulic, reversible
						
						
							Gearbox
							Housing: Cast
						
						Brakes
							Brake System Type
							Multiple wet disk, spring applied hydraulic released
						
						Electric
							Alternator
							12 V	(200 amp)
						
						Operational
							Operating Speed
							Track machine travel speed: 0 to 5.6 mph (0 to 9.0 km/h) | Maximum fan: 930 rpm
						
						Cab
							Air Conditioner Output
							Pressurized cab with air conditioning and heating
						
						
							Seat Type
							Air suspension with swivel
						
						Lights and Safety
							Lighting
							Cab: Four halogen head lights and four working light-emitting diode (LED) lights | Auxillary: four loading Four LED lights | Service: Two LED lights on topper boom and two halogen lights on engine/cooling package compartment
						
						Dimensions
							Dimensions
							Standard chain and shoes: 22 in. (560 mm) | Maximum whole topper reach: 13.75 ft (4.2 m) | Basecutter: Standard disc diameter 23 in. (58.4 cm) | Inside scrolls approach angle: 46 degree (angle) | Basecutters: Center to center distance 70.9 in. (180 cm) | Discs center distance: 24.8 in. (63 cm) | Drum center distance: 15 in. (38.1 cm) | Total swing angle: 170 degree (angle)
						
						
							Fan Diameter
							5 ft (1.5 m)
						
						
							Width
							Track tread: 11.8 ft (3.6 m) | Blade: 3.74 in. (9.5 cm) | Elevator: 44.1 in. (112 cm)
						
						Capacities
							Fuel Capacity
							300 gal. (1135 L) | Diesel Exhaust Fluid (DEF) (Tier 4 Engine only): 20.7 gal.	(78.2 L)
						
						
							Oil capacity
							Hydraulic: 81.6 gal. (309 L)
						
						Weights
							Weight
							78,363.2 lb (35,545 kg)
						
						Features
							Features
							Crop dividers: Float control | Chopper: Standard blade configuration: Ten blade (five per drum), differential | Sprocket: Five-segment, bolt-on sprocket | Rollers: Eight bottom rollers and two carrier rollers | Radio: Standard premium with Bluetooth® wireless | GPS guidance: AutoTrac ready standard | Connectivity: JDLink™ ready | Shock absorption: Nitrogen accumulator | Severing disc: Eight bolt-on blades | Crop divider assemblies: Two side assemblies and one center assembly	 | Center crop divider assembly scrolls: Includes two inside scrolls | Factory hard surfacing: Skirts, slip-on shoes, toes | Tilt control: Hydraulic | Blades: Three bolt-on blades per disk | Knockdown roller assemblies: Two assemblies consisting of one front and one lower roller each | Discs per box: two | Legs: Vertical with bolt-on wear plates | Number of blades per disc: five | Buttlifters: two | Feed train assemblies: Two front split feed trains and one rear common feed train | Feedroller train: Each feed train has upper floating rollers and lower feedrollers | Front split feed trains number of rollers: Each feed train has four upper rollers and four lower rollers including the buttlifter | Rear feed train number of rollers: Three upper rollers and four lower rollers including the transition roller | Fan number of blades: four | Hood rotation: Hydraulically controlled | Sprocket drive: Hydraulic motor driven, reversible | Elevator swing: Hydraulically controlled, trunnion cylinders
						
						
							Adjustability
							Hydraulic height: Synchronized front and lower roller travel | Chain: Grease cylinder
						
						
							Track Type
							Welded guides with bolted wear plates
						
						
							Knife Quantity
							Side: Two | Center: One
						
						
							Construction Material
							Wear ring: Highly abrasive-resistant steel
						
					 
           
            